收藏本站
Caution
1. Use a 20W soldering iron with a maximum tip diameter of 1.0 mm.
2. The soldering iron should not directly touch the inductor.
5. Cleaning
◆Cleaning conditions
1. When cleaning the PC board after the Inductors are all mounted, select the appropriate cleaning solution according to the type of flux
Precautions
Technical
considerations
used and purpose of the cleaning（e.g. to remove soldering flux or other materials from the production process.）
2. Cleaning conditions should be determined after verifying, through a test run, that the cleaning process does not affect the inductor's
characteristics.
◆Cleaning conditions
1. The use of inappropriate solutions can cause foreign substances such as flux residue to adhere to the inductor, resulting in a degradation
of the inductor's electrical properties（especially insulation resistance）.
2. Inappropriate cleaning conditions（insufficient or excessive cleaning）may detrimentally affect the performance of the inductors.
（1） Excessive cleaning
a. In the case of ultrasonic cleaning, too much power output can cause excessive vibration of the PC board which may lead to the
cracking of the inductor or the soldered portion, or decrease the terminal electrodes' strength. Thus the following conditions
should be carefully checked;
Ultrasonic output Below 20W/?
Ultrasonic frequency Below 40kHz
Ultrasonic washing period 5 min. or less
6. Post cleaning processes
◆Application of resin coatings, moldings, etc. to the PCB and components.
1. With some type of resins a decomposition gas or chemical reaction vapor may remain inside the resin during the hardening period or while
left under normal storage conditions resulting in the deterioration of the inductor's performance.
Precautions
2. When a resin's hardening temperature is higher than the inductor's operating temperature, the stresses generated by the excess heat
may lead to inductor damage or destruction.
3. Stress caused by a resin's temperature generated expansion and contraction may damage inductors.
The use of such resins, molding materials etc. is not recommended.
7. Handling
◆Breakaway PC boards（splitting along perforations）
1. When splitting the PC board after mounting inductors and other components, care is required so as not to give any stresses of deflection
or twisting to the board.
2. Board separation should not be done manually, but by using the appropriate devices.
◆General handling precautions
1. Always wear static control bands to protect against ESD.
2. Keep the inductors away from all magnets and magnetic objects.
Precautions
3. Use non-magnetic tweezers when handling inductors.
4. Any devices used with the inductors（ soldering irons, measuring instruments） should be properly grounded.
5. Keep bare hands and metal products（i.e., metal desk）away from chip electrodes or conductive areas that lead to chip electrodes.
6. Keep inductors away from items that generate magnetic fields such as speakers or coils.
◆Mechanical considerations
1. Be careful not to subject the inductors to excessive mechanical shocks.
（1） If inductors are dropped on the floor or a hard surface they should not be used.
（2） When handling the mounted boards, be careful that the mounted components do not come in contact with or bump against other
boards or components.
8. Storage conditions
◆Storage
1. To maintain the solderability of terminal electrodes and to keep the packaging material in good condition, care must be taken to control
temperature and humidity in the storage area. Humidity should especially be kept as low as possible.
Recommended conditions
Precautions
Technical
considerations
Ambient temperature Below 40℃
Humidity Below 70% RH
The ambient temperature must be kept below 30℃. Even under ideal storage conditions inductor electrode solderability decreases as
time passes, so inductors should be used within 6 months from the time of delivery.
*The packaging material should be kept where no chlorine or sulfur exists in the air.
◆Storage
1. If the parts are stocked in a high temperature and humidity environment, problems such as reduced solderability caused by oxidation of
terminal electrodes and deterioration of taping/packaging materials may take place. For this reason, components should be used within
6 months from the time of delivery. If exceeding the above period, please check solderability before using the inductors.
? This catalog contains the typical specification only due to the limitation of space. When you consider the purchase of our products, please check our specification.
For details of each product (characteristics graph, reliability information, precautions for use, and so on), see our Web site (http://www.ty-top.com/) .
i_mlci_prec_e-E02R01
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
A9BBA-0704E FLEX CABLE - AFJ07A/AE07/AFJ07A
NCV8405ASTT3G IC DRIVER LOW SIDE SOT-223-4
NCV8405STT3G IC DRIVER LOW SIDE SOT-223-4
A9CAA-1204F FLEX CABLE - AFG12A/AF12/AFE12T
MAX4824ETP+T IC 8CH RELAY DVR PWR SAVE 20TQFN
A9CAA-0402E FLEX CABLE - AFK04A/AE04/AFH04T
A9CCG-0802F FLEX CABLE - AFG08G/AF08/AFG08G
A9AAT-1008E FLEX CABLE - AFH10T/AE10/AFH10T
相关代理商/技术参数
HK-1005-12NJTK 功能描述:固定电感器 12nH 300mA 5% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK100512NK-T 功能描述:固定电感器 INDCTR HIFREQ MLTLYR 0402 12nH 10% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK100515NG-T 制造商:TAIYO YUDEN 功能描述:IND CHIP ML 15NH 2% 100MHZ 8Q-FCTR 300MA 0402 - Tape and Reel
HK100515NJ 制造商:TAIYO YUDEN 功能描述:IND SMD 15NH 5% 250MA 0402
HK100515NJ-T 功能描述:固定电感器 INDCTR HIFREQ MLTLYR 0402 15nH 5% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK-1005-15NJTK 功能描述:固定电感器 15nH 300mA 5% RoHS:否 制造商:AVX 电感:10 uH 容差:20 % 最大直流电流:1 A 最大直流电阻:0.075 Ohms 工作温度范围:- 40 C to + 85 C 自谐振频率:38 MHz Q 最小值:40 尺寸:4.45 mm W x 6.6 mm L x 2.92 mm H 屏蔽:Shielded 端接类型:SMD/SMT 封装 / 箱体:6.6 mm x 4.45 mm
HK100515NJ-TV 功能描述:15nH Unshielded Multilayer Inductor 300mA 460 mOhm Max 0402 (1005 Metric) 制造商:taiyo yuden 系列:HK 包装:剪切带（CT） 零件状态:有效 类型:多层 材料 - 磁芯:铁氧体 电感:15nH 容差:±5% 额定电流:300mA 电流 - 饱和值:- 屏蔽:无屏蔽 DC 电阻（DCR）:460 毫欧最大 不同频率时的 Q 值:8 @ 100MHz 频率 - 自谐振:2.3GHz 等级:AEC-Q200 工作温度:-55°C ~ 125°C 频率 - 测试:100MHz 安装类型:表面贴装 封装/外壳:0402（1005 公制） 大小/尺寸:0.039" 长 x 0.020" 宽（1.00mm x 0.50mm） 高度 - 安装（最大值）:0.022"（0.55mm） 标准包装:1
HK100515NK 制造商:TAIYO YUDEN 功能描述:1 ELEMENT, 0.015 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR, SMD